MODEL: M2XRP2
RS-232-C level
[5] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE or UL
Pulse sensing: DC coupled or capacitor coupled selectable
with DIP SW
Low-end cutout: 100 msec. – 100 sec. or no cutout
programmable
/CE: CE marking
/UL: UL approval, CE marking
Other Options
blank: none
INPUT SPECIFICATIONS
Excitation: Shortcircuit protection; 20 mA max. at
shortcircuit
/Q: Option other than the above (specify the specification)
Maximum frequency: 200 kHz
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
Frequency ranges:
0 – 10 mHz, 0 – 100 mHz, 0 – 1 Hz, 0 – 10 Hz, 0 – 100 Hz,
0 – 1 kHz, 0 – 10 kHz, 0 – 100 kHz
(Choose 100 kHz range to set the zero/span frequencies
lower than -100 kHz (higher than 100 kHz in the reverse
direction) or higher than 100 kHz (higher than 100 kHz in
the forward direction.))
/C02: Polyurethane coating
/C03: Rubber coating (UL not available)
TERMINAL SCREW MATERIAL
/S01: Stainless steel (UL not available)
Minimum pulse width time requirement: 2.5 μsec.
Minimum span: 10 % of the selected frequency range
Noise filter: See table 2
RELATED PRODUCTS
? PC configurator software (model: JXCON)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
■ Open Collector
Input requirements
EXCITATION
5 V
SENSING
OFF
ON
Approx. 5 V
Approx. 10 V
≥200 kΩ
≥200 kΩ
≤200 Ω
≤200 Ω
12 V
Amplitude: 5 - 12 V
Detecting level:
GENERAL SPECIFICATIONS
Construction: Plug-in
5 V excitation: 1 V
12 V excitation: 2 V
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
(Detecting voltage in the internal circuit.
For open collector input, be sure to re-adjust the voltage
back to 1 V (5 V excitation) or 2 V (12 V excitation) if it has
been changed for other input types.)
Detecting pulse edge: OFF to ON
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -15 to +115 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
Configuration: Via PC Configurator Software (model:JXCON)
on the Windows PC connected to
the front jack.
If not specified, the input range is 0 Hz – 1 kHz.
■ Voltage Pulse
Waveform: Square or sine
Input impedance: 10 kΩ min.
Pulse amplitude: 0.1 – 30 Vp-p
Pulse amplitude Range: See table 1.
Max. voltage between input terminals: See table 1.
Sensitivity Scale: See table 1.
Programmable features include:
· I/O type and range
· Zero and span adjustments
Detecting level: -2 – +4 V
· Low-end cutout
Detecting pulse state: A pulse rise detected when the input
voltage goes above the detecting level;
a pulse sink detected when it goes below the level.
If not specified, the input range is 0 Hz – 1 kHz.
■ RS-422 Line Driver Pulse
· Linearization
Status indicator LED: Red LED; Flashing patterns indicate
different operating status of the transmitter.
Input monitor (PL1): Green LED blinks according to the input
phase A.
Receiver: Conforms to RS-422
Input monitor (PL2): Green LED blinks according to the input
phase B.
If not specified, the input range is 0 Hz – 1 kHz.
Excitation adjustment: 5V or 12V DC
Configurator connection: 2.5 dia. miniature jack;
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.12 Page 2/6